How We Repair Your Duraflame Infrared Heater
Furnaces, boilers, heat pumps, radiant systems and space heaters produce heat with burners, elements or a heat pump circuit, protected by safety controls.
Every Duraflame model has its own parts list, so we start with the model and serial number on the rating label. That tells us the correct parts and any known issues or service bulletins for your unit.
Safety first: Install carbon monoxide detectors near sleeping areas. If one sounds, leave the home and call 911.
Common Infrared Heater Problems We Fix
No heat
A dirty flame sensor, a failed igniter, a tripped limit switch, a thermostat problem or a pilot that will not stay lit.
Short cycling
An overheating furnace from a dirty filter, a faulty limit switch or an oversized system.
Heat pump blowing cool air in heat mode
A failed reversing valve, defrost control or low refrigerant.
Boiler leaking or losing pressure
A failed relief valve, expansion tank or leaking fitting.
Strange noises
Worn blower motor bearings, a cracked heat exchanger or air in boiler lines.
Quick Checks Before You Call
These are safe for most owners and sometimes solve the problem without a visit:
- Replace the furnace filter
- Check the thermostat setting and batteries
- Make sure the furnace power switch and gas valve are on
Still not working? Call (844) 442-1500 or try our troubleshooting wizard.
Our 5-Step Repair Process
- Call or book onlineTell us what your Duraflame infrared heater is doing and when it started. We schedule the first available visit.
- DiagnosisThe technician checks power, controls and the parts most likely to fail, using the model's service data and test modes.
- Upfront quoteYou get the cause, the repair and the price before any work starts. If repair does not make sense, we tell you.
- RepairWe install original or equivalent parts matched to your model and clean up when we are done.
- Test and warrantyWe run the appliance through a full cycle to confirm the fix. The repair is covered by our 90-day parts and labor warranty.
Parts We Replace Most Often
- Igniters and flame sensors
- Limit switches
- Blower motors and capacitors
- Gas valves
- Circulator pumps
- Reversing valves and defrost boards
Cost and Lifespan
Most infrared heater repairs cost $150–$650 including parts and labor, and these appliances typically last 15–25 years. These are national estimates: your exact price comes after the diagnosis. Use the repair vs replace calculator to compare.
Keep It Running Longer
- Keep vents and returns open
- Change filters regularly
- Have gas heating checked each fall
Infrared Heater Repair in Florida
We repair infrared heaters in 349 cities and towns across Florida. Long, humid summers in Florida push refrigerators, ice makers and AC units in homes across the state hard for most of the year.
Frequently Asked Questions
How much does Duraflame Infrared Heater Repair cost in Florida?
Most infrared heater repairs fall between $150–$650 including parts and labor. The final price depends on the part that failed and your model. You get an exact quote after the diagnosis and before any work starts.
Can you repair my infrared heater today?
Same-day visits depend on technician availability in Florida. Call (844) 442-1500 early in the day for the best chance of a same-day or next-day appointment.
Is the repair guaranteed?
Yes. Parts and labor are covered by our 90-day warranty. If the same problem comes back within that time, we return and fix it.
Do you work on all Duraflame models?
We repair current and older Duraflame models. Some discontinued parts can be hard to find; if that is the case for your model, we tell you before you pay for a repair.
Should I repair or replace my infrared heater?
A infrared heater typically lasts about 15 to 25 years. If yours is well inside that range and the repair costs less than half the price of a new one, repairing usually makes sense. Near the end of its life, or when the repair costs more than half of a replacement, replacing is often the better value. We give you an honest opinion either way.